AM1011EX switch input isolation safety barrier accepts switches from danger zones or proximity switch inputs, transmitting to safe zone relay outputs through safety barrier isolation, where it is possible to select settings as input and output of non-inverted or inverted control, which also comes with the functions of inspecting and reporting disconnections and displaying messages on those disconnections. AM1011EX requires an independent power supply whereby the power, input, and output are isolated.

Key technological parameters:

• Number of channels: 1

• Ex mark: [ Ex ia ]ⅡC

• Applicable areas: Installed in safe zones and can be connected with intrinsic safety instruments in zero zones,ⅡC, and T4-T6 danger zones.

• Power supply voltage: 20-35V,d.c.

• Current consumption: ≤ 40mA (24V supply, when relay contacts are closed)

• Relay output characteristics of the safe side: Response time: ≤20ms; Load type: resistive load

Drive capability: 250V,a.c.,2A or 30V,d.c.,2A

• Danger side:

Input signal: Switch, proximity switch

Open circuit voltage: ≈8V;Short circuit current: ≈8mA

• Input and output characteristics (set as non-inverted control)

When field switch is closed or input circuit current > 2.1mA, the output relay circuit is closed, and the channel’s yellow indicator light will turn on. If the field switch circuit or input circuit current < 1.2mA, the output relay circuit will open, and the channel’s yellow indicator light will go off.

Roles of switch settings:

Status

K1

K3

ON

Inverted input and output

No function for inspecting disconnections

OFF

Non-inverted input and output

Includes function for inspecting disconnections

Note: When the switch input requires the function for inspecting disconnections, it is recommended to connect 10kΩ resistors in parallel on both ends of the switch.

• Power source protection: Reverse polarity protection in power source

• Electromagnetic compatibility: Compliant with GB/T 18268(IEC 61326-1)

• Dielectric strength: Non-intrinsic safety terminal - intrinsic safety terminal ≥2500V, a.c; Source - Non-intrinsically safe terminal ≥500V, a.c.

• Insulation resistance: Source, between the shell and the non-intrinsic safety terminal and intrinsic safety terminal ≥100MΩ;500V.d.c.

• Weight: Around 110g

• Field equipment applicable: Equipment such as switches and DIN19234-compliant NAMUR proximity switch (including: intrinsic safety voltage switch, temperature switch, and liquid level switch)

Usage environment:

(1) The surrounding environment should not have electromagnetic induction effects such as strong vibrations, shocks, major currents and sparks, and there should not be any substance in the air that would corrode the chromium, nickel, or silver plating, and there should not be flammable or explosive substances.

(2) Continuous working temperature: -20℃ - +60 

(3) Storage temperature: -40℃ - +80℃;

(4)Relative humidity: 10% - 90%RH.

Applications:
Safety certification:

Certification by the NEPSI (National Supervision and Inspection Centre for Explosion

Protection and Safety of Instrumentation)

Certification standards: GB 3836.1-2000 and GB 3836.4-2000

Highest voltage (U m)=250V r.m.s.

Certification parameters (between terminals 7 and 8):

Uo=10.5V,Io=14mA,Po=37mW

ⅡC:Co=2.4 μF , Lo=165mH

ⅡB:Co=7.2 μF , Lo=840mH

ⅡA:Co=19.2μF,Lo=1320mH

Intrinsic safety explosion-prevention circuit system:

When connecting the isolation safety barrier with the field intrinsic safety instrument to form an intrinsic safety explosion-prevention circuit (intrinsic safety circuit) system, the following should be verified before using the system. 

1) The field intrinsic safety instrument’s explosion-prevention level has to suit the usage environment, and the system has to be recognised by State-authorised explosion-prevention product certification organisations and be installed with a certified explosion-prevention instrument.

2) The certification parameters between the isolation safety barrier and field intrinsic safety instruments are explicit and compliant with requirement 12.2.5.1 of GB 3836.15-2000.

3) If there are non-explicit parameters, it will be necessary to verify the intrinsic safety circuit system with the State-authorised explosion-prevention product certification organisation.

Installation:
The isolation safety barrier should be installed in a safe place, and be compliant with relevant regulations under the “Installation and Acceptance Standards for the Installation of Electrical Equipment in Explosion-prone and Fire-prone Environments” under the GB 50257-1996, “Section 15 of Electrical Equipment for Use in Environments with Explosive Gases: Electrical Installations in Danger Zones (except coal mines)” under the GB 3836.15 – 2000, “Section 13 of Electrical Equipment for Use in Environments with Explosive Gases: Inspection of Electrical Equipment for Use in Environments with Explosive Gases” under the GB 3836.13-2003, and “Section 16 of Electrical Equipment for Use in Environments with Explosive Gases: Inspection and Maintenance of Electrical Devices (except coal mines)” under the GB 3836.16-2006.